Site Home
  Category
  Site Home
  2M SSB
  ATV
  CT WIN Introduction
  Emergency Power
  JPole Antennas
  Microwave & Up
  Military Scanner Freqs
  Packet Radio
  Sound Card
  SSTV

Testing Session
Next test session is Sept 8th


  Microwave Communications

Have you ever worked a band above 440? Probably not. With the exception of 1296 MHz, I am not aware of any commercially made ham transceivers available for bands above 440. There are many homebrew devices and kits available, but only ICOM and Kenwood ever produced commercial type accepted transceivers for these bands, limited to one model each. These are the last frontiers of the amateur radio homebrew community, where the pioneer spirit still reigns!

The Start!

I have been interested in these frequencies from long before I was a licensed ham. I built a downconvertor for 1296 back in the early eighties to listen to the then proposed 1296 beacon on an Oscar bird. The downconvertor was based on a design I originally found in the ARRL Handbook. It used an interdigital filter/mixer combination with a Schottky diode for the active element in the mixer. The receiver was a shortwave receive tuned in the 10M band. The LO chain was hard to get working with my limited resources and I was never really sure it was working right, but I could hear lots of signals, mainly beacons (I think) from aircraft on the nearby airbase and control links. Never heard any ham activity at the time, though. I later became licensed and discovered that there are extremely few hams in this area with the interest, much less station capabilities to work above 440. There was some activity on 2M and 432 sideband, but nothing serious. There has been a revived interest in these bands lately and I'm hoping to exploit that.

GunnPlexers

Once upon a time I decided I would build some 10 GHz stations. This started when a couple of X-Band GunnPlexers ended up in my hands. These are magnificent devices, available from Advance Receiver Research, which functions as a sort of "all-in-one" RF head for microwave work.

Figure 1 - GunnPlexers Figure 2 - GunnPlexer Block Diagram

The Gunn diode, in it's own resonant cavity, oscillates at 10GHz and acts as the LO for both transmit and receive, simultaneously. A small iris couples the LO energy into the main cavity, which contains a ferrite bar and a Schottky diode. The ferrite bar acts as a circulator and isolator, coupling the incoming signal and some of the LO energy into the mixer, the Schottky diode. There is a varactor diode mounted in the Gunn oscillator cavity which can be used to change the LO frequency. This allows both modulation (WBFM) and AFC to be exercised. The one drawback to the Gunn diode oscillator is that they have a sensitivity to temperature that shows itself as a drift in frequency. Watching the output on my spec-an, I can hold the GunnPlexer body in my hand and watch the signal walk off the display in real time. This makes it hard to use these devices for narrow band work. However, in the wideband field, where the temperature drift can be compensated with AFC techniques, these things are excellent sources of RF.

I have considered injecting a crystal controlled signal into the cavity to acheive a "sympathy lock" effect, but have never gotten around to it. My idea is to use a surplus PC clock crystal at 50 MHz blasting away on the varactor diode, since the 205th harmonic of 50 MHz falls on 10.25 GHz. According to the technical books, only a little signal (20 to 30 db down from the Gunn power level) is required to achieve lock. This technique might yield some interesting results if I don't destroy the varactor in the process.

Another interesting project is to use the GunnPlexers as data transceivers. With the wide band nature of data transmissions, the drift of a GP module is of little consequence. What drift is present can be compensated for with standard AFC loops. Here is an example of such a project.

Narrow Band 10 GHz

Section on Narrow band stuff, write up on Didier's efforts.

Linear Transvertors

Write about linear transvertors!

Antennas

Antennas for microwave bands can be built or scrounged. Horns are the most common antenna structure found in microwave use. Horns can be bought commercially, or can be constructed from various materials such as sheet brass, copper or copper-clad pc board. Dishes can be employed at frequencies as low as 2400 without becoming to unwieldy. They are particularly effective above 5 GHz, where thier small size can contribute a large gain, especially in concert with a horn feed. Dish feeds can be constucted from various scrap materials as well, a common feed being printed on circuit board material. For satellite work, helical feeds sued with surplus Direct-TV dishes can be employed with great success. Here is a great ham opriented dish site!

Summary

Links

HOME | JOIN | LOGIN

VIEW DX SPOTS | ADD A DX SPOT | SEARCH DX SPOTS | SHOW DX SPOTS | LOGOUT

This application and data entered thereinto is the property of KB4OID.
Click here for our privacy and copyright statements.